Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
Almost everyone may have his or her own views in relation to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't specifically rocket science, however it does require solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably tough job. If the old tub is conveniently accessible, the task can move easily; if you need to open a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will need a helper to leave the old tub as well as set in the new one. Make sure you have actually qualified on your own for the work and are comfortable trying it. As opposed to working with a specialist to take over a halfway-completed job, it is better to consider utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This short article will certainly aid you install a brand-new bathtub in your washroom if you have actually already acquired a new tub as well as do not need to alter the setup of your previous water system pipes.
Your tools and also product checklist need to consist of the following:
Preparing for the Setup
First of all, the supporting structure provided with the bathroom should be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the limited gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Making use of both wood boards under its feet, put the tub in the needed position. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Activate the water system and also examine all joints and new pipework for leaks as well as tighten them if necessary. Fill the tub and likewise check the overflow outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and also securing around the bath tub ought to wait up until the bath tub has been made use of at the very least once as this will certainly settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the tap as well as the sink. Safeguard the tap in place with the supplier provided backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bath and also the tiling, leading to issues with wetness as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealant can break fairly very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on Installing A Bathtub? Leave a remark down below. We would be pleased to hear your insights about this blog entry. Hoping that you visit us again before long. So long as you enjoyed reading our page plz make sure you remember to pass it around. Thanks for your time. Please pay a visit to our blog back soon.
Immediate response? Call. Report this page